A time schedule or object monitoring line is set up, but no date proposal appears in the Date Proposal List or on the Date Proposal Worksheet page. maintool only shows a date if the time schedule, the object monitoring line and the object are active, a new date is possible and the date matches the period, options and filters of the date proposal name. Check the following points.
On the time schedule or object monitoring line
| Cause | Solution |
| The Status field of the time schedule is Blocked or Expired, or the status of the object monitoring line is Blocked, Deleted or Expired. For object monitoring lines, the status of the related time schedule also counts. Date proposals are only created with a blank status. | Clear the status if dates are to be created again. maintool sets Expired if the next date would be after the Scheduling End Date-Time. In that case, extend or clear the scheduling end date. See Limit, block or phase out a time schedule. |
| New Date possible is disabled, for example because the work order for the last date has not been finished yet. | See No new date: "New Date possible" is off. |
| Next Action at Date-Time is blank because the Time Interval or the starting point is missing (Time interval to Start on the time schedule, Starting Date-Time on the object monitoring line). | Enter both values. maintool calculates the first date from the starting point plus the Time Interval. |
| The technical object of the object monitoring line is blocked. | No date proposals are created for blocked objects. Remove the block on the object if the work is to be planned again. |
| Type of monitoring Counter or Attrition / Consumption: no performance characteristics have been posted for the period, or the last posted value has not yet reached the next value (Next Action by Value, taking the Tolerance Value into account). Without an Interval (for attrition / consumption also without an Initial Value), a date proposal is never created. | Post the performance characteristics, see Record and post performance characteristics in the journal, and check the Interval and Initial Value of the object monitoring line. |
| Type of monitoring Threshold / Range: no posted measured value is outside the defined thresholds or deviates more than allowed from the previous value. | Not an error: with this type of monitoring, a date proposal is only created by such a measured value. See Set up threshold monitoring with an activity. |
| The object monitoring line belongs to a mounting position and has a type of monitoring other than Date. | No performance characteristics are recorded for mounting positions. Here, date proposals are only created with the type of monitoring Date. |
On the date proposal name and the period
| Cause | Solution |
| The matching source is not enabled for the date proposal name: Time Schedule for time schedules without object reference, Object Monitoring Line for time schedules of the type Object Monitoring Template. Both are disabled for newly created names. | Enable the option in the Date Proposal Names list or on the Date Proposal Worksheet page under Show Options. See Set up date proposals for work planning. |
| Next Action at Date-Time is outside the period. With View as Net Change, you only see dates between Starting Date and Ending Date, so no older, overdue dates. | Choose Balance at Date or a suitable period. In the Role Center, the period extends to the end of the future period of the Role Center setup, see Maintenance – Workplanner Role Center. |
| A filter excludes the date, for example Res. Department No., Person in Charge No., Type of Activity Code, Shift or Work Order Duration from/until. The values come from the time schedule. With a shift or a Starting Time/Ending Time, the time of the date also counts. | Check the filters of the date proposal name and on the Date Proposal Worksheet page under Show Filters. In the Role Center, the Responsible for Department field of the Role Center setup applies instead of the department filter. |
| The date proposals have not been recalculated since the change: Automatic Update Lines is disabled for the date proposal name (page title (Not Actual)), or the Calculation Interval in the Role Center is Hourly or Daily. | Choose Update on the Date Proposal Worksheet page or in the Date Proposal List. |
| You also expect later dates, but only see the next date. | Later dates are preview dates. They only appear with the Preview option and if a Date Preview Period is set up. See Set up the date preview. |
Related articles
- No new date: "New Date possible" is off
- View and filter date proposals
- Set up date proposals for work planning
- Create a work order from a date proposal
Related to