A work order cannot be finished or closed

  • Updated

You want to set a work order to Finished or Closed, but maintool stops the status change with a message. The status then remains unchanged. Find the message in the table, fix the cause and change the status again.

Messages when finishing and closing

The Applies to column shows for which target status the check runs. When you change to Closed, all checks for Finished also run if the work order has not yet been reported finished.

Message Cause Solution Applies to
Error message for the Blocked field The work order is blocked. Disable Blocked on the General FastTab of the work order card. Finished, Closed
You can not change Work Order Status from … to …, because there is at least one unconsidered Work Order Status! The work order is still in Planning, or another mandatory status lies in between. Execution is mandatory and must not be skipped. First set the work order to Execution or to the missing status. See Schedule a work order and set it to execution. Finished, Closed
The field "Result" is missing for job: … A result is mandatory for the activity named but has not been entered. Enter the result. See Answer a checklist in the work order. Finished, Closed
The current job has not been carried out jet: … The activity is not marked as finished, and Check Work Order Texts Finish is enabled in the Work Order Management Setup (General FastTab). Mark the activity as finished. See Answer a checklist in the work order. Finished, Closed
Not all mandatory informations are filled in Instruction No. …. The activity is not marked as finished, and mandatory items of its checklist are unanswered. Answer the mandatory items of the checklist. Finished, Closed
Error message for the Checklist Perf. Jnl. Templ. or Checklist Perf. Jnl. Batch field The field is empty in the Work Order Management Setup (Checklist FastTab). maintool checks it every time a work order is reported finished, even without a checklist in the work order. Fill in both fields. See Set up work order management. Finished, Closed
Error message for the Line No. (Object Mon. Line) field An activity has a Monitoring Template Code but no reference to an object monitoring line. Does not apply if the reference object is a mounting position. Contact your maintool partner. Finished, Closed
You have to reporting-finish the remaining … in work order … manually. The question about open origin lines was answered with No. Change the status again and confirm the question with Yes. Or report the origin lines as finished individually beforehand, or mark them as not executed. See Finish and close a work order. Finished, Closed
Work Order Status did not change! The question about reserved quantities was answered with No. Change the status again and confirm the question with Yes. maintool then cancels the reservations of the item lines. Finished, Closed
You can not change Work Order Status from … to Closed, because there is at least one unconsidered Work Order Feedback! There is an unposted work order feedback for the work order, for example from maintool mobile. Post or delete the work order feedback. See Create and post a work order feedback. Closed
… because there is at least one unconsidered Purchase Quote! or … because there is at least one unconsidered Purchase Order! A purchase quote or purchase order still contains lines for this work order. Complete the purchase quote or purchase order, or remove the lines for this work order. See Create a purchase quote or purchase order from a work order. Closed
The Assignment of Technical Component … could not be Installation. The reference object is Technical Component, and the technical component named has the assignment Installation. Change the assignment of the technical component before you close the work order. Closed
Error message about the user ID or email address Send E-Mail is enabled for the work order category, and information required for sending is missing, for example the email address in the user setup. Add the missing information. See Automatic email notifications. Finished, Closed

Notes

  • The same checks run if you change the status while posting a work order feedback, with Report as Planned or with Post to G/L.
  • If you change the status of several work orders at once, maintool does not show a message per work order. The work orders that were not changed remain marked. Change their status individually to see the message.

Related articles

Related to

Was this article helpful?

0 out of 0 found this helpful

Have more questions? Submit a request