Set up technical facility management

  • Updated

Before you create component addresses, mounting positions, technical components and vehicles, set up technical facility management. This article shows the recommended order of setup and describes the Technical Facility Management Setup page with the number series and the rules for component places.

Order of setup

Ideally, set up technical facility management in this order. Each step builds on the previous ones.

  1. Define the basic settings and number series on the Technical Facility Management Setup page (this article).
  2. Enter the source codes for technical facility management: Source codes for work order management (Technical facility management section).
  3. Create component address groups and catalogs such as component groups, classes, types and types of vehicle: Set up master data for technical facility management.
  4. Create locations for technical objects: Locations of technical objects.
  5. Create technical specifications, ranges of values and data sheet templates: Technical specifications and data sheets – basics, Create ranges of values, Create a technical specification, Create and assign data sheet templates.
  6. Check the journal templates for technical components and performance characteristics: Set up journal templates.
  7. Create object monitoring templates for counters, thresholds and consumption: Set up object monitoring templates.
  8. Create types of damage, figures of damage and causes of damage for work order requests and work orders: Set up damage codes.
  9. In the User Setup, assign a Component Address Group to each user (see below).

Then build the equipment structure, see Plan the equipment structure.

Open the Technical Facility Management Setup

Search for Technical Facility Management Setup using the search (Alt+Q) and open the page. Alternatively, you find it in the Maintenance Role Center under Setup › Technical Facility Management. The page contains the FastTabs General and Numbering.

General FastTab

Field Meaning
Component Address Levels Colored Currently not evaluated in Business Central.
Component Address Structuring Key Sort order in which maintool processes the component addresses when building the structure, for example with the Recreate Technical Structure report. You can only select sort orders in which Level comes directly before Component Address from. The default is the sort order by Level and Component Address from.
Technical Component Levels Colored Currently not evaluated in Business Central.
Technical Component Structuring Key As for component addresses, for technical components. You can only select sort orders in which Level comes directly before Component from. The default is the sort order by Level and Component from.
Bind Component Place Specifies whether a component place may or must be specified when a technical component is installed in a higher-level technical component (Component from field). maintool checks the setting when posting in the Technical Component Journals.
  • Never: The Component Place field must be empty.
  • Optional (default): A component place can be specified.
  • Always: The Component Place field must be filled in.
Installations in a mounting position or in a vehicle are not affected by this setting.
Assignment of Component Place to Technical Component Specifies how many technical components may sit at one component place.
  • 1 by 1: Only one technical component may sit at a component place. maintool checks this on the technical component card, in the journal line and when posting.
  • 1 by n (default): Any number of technical components may sit at a component place.
You can only switch to 1 by 1 if no component place has more than one technical component. Otherwise, the message The Assignment of Component Place to Technical Component could not modified to 1 by 1, because there are some component places existing, which had more than one technical component bound. appears.
Load Pictures in Equipment-Informationcenter On (default): The Equipment Information Center shows pictures of the technical objects in the structure view. With large equipment structures, this can increase the loading time; in that case, turn the setting off.

To learn how to create and use component places, see Technical component place.

Numbering FastTab

In each field, select an existing number series or create a new one. If you create a new object without a number, maintool assigns the next number of the series. If no number series is entered, maintool cancels creating an object without a number with an error message. You can only enter a number manually if Manual Nos. is enabled in the number series.

Field Number series for Example
Component Adress Nos. Component addresses AK00001
Mounting Position Nos. Mounting positions EP00001
Technical Component Nos. Technical components TK00001
Document Nos TC-Attachment Document number of the entry that maintool posts when you run the Start History action for a technical component (on the card, in the list of technical components or in the Equipment Information Center). Without a number series, maintool posts the entry without a document number. TKB000001
Vehicle Nos. Vehicles FZ00001

To learn how the history of a technical component works, see Start the history of technical components.

User setup

A mounting position can be assigned to component addresses from several component address groups. If you open the Equipment Information Center from such a mounting position (or from a technical component or vehicle in it), the Component Address Group field in the User Setup determines which structure maintool shows.

  1. Search for User Setup and open the page.
  2. Create a line for each user who works with the equipment structure, if none exists yet.
  3. In the Component Address Group field, select the group the user mostly works with.

If the user setup entry is missing, the Equipment Structure action is not available for such mounting positions, and maintool shows a notification. See Use the Equipment Information Center.

Related articles

Related to

Was this article helpful?

0 out of 0 found this helpful

Have more questions? Submit a request